Відео

I have a dehumidifier with R32 Freon. Is it actually okay to mix different kinds of freon? I don't seem to be able to find a refill kit for R32. If it can be mixed with something else, what should I get to mix with it?

Heya Lou, I have cold water, and my power vent is running.... when I bridge the two connectors I get nothing... do you still think it's the vacuum switch? also what is the model number for the vacuum switch? Thanks

What is the part number?

I've had a joke for years that all I need is for someone to tell me where I can get 2 atoms of hydrogen and 1 atom of oxygen and I can make water!

Thanks from New Zealand 🤙

What happens if u shoot it without the stock on?

Well played sir! No Tom Foolery, just straight forward.

I followed exact steps of this video and it WORKED! Only thing I did different was used duct tape to hold the clip open!

Okay we performed this today. Worked absolutely perfectly!! Excellent video with all steps explained the way we can understand. Just a note, we used liquid bleach concentrated we picked up at Walmart. After about 1 hour the smell of bleach was all thru the house. We turned on 3 ceiling fans and opened all windows. This is a step that we will do first from now on BEFORE we start the cleaning process. Otherwise all was GREAT! I love it when a UA-cam video actually works. Thanks again.

Brilliant

What if I want to build it out side?

Won't the sand clog up the sump pump?

I have watched countless minibike videos and builds, and none of them have covered as much ground as this one. This is the best mini bike video on UA-cam in my opinion for explaining how all of these different parts / systems work together.

I like you video. But how did you get the 4 mounting bolts back in. I have a 1958 Ford Tractor with a front loader. Got the new hub installed, with two bolts installed. Can't figure out how to get the other 2 bolts installed. Do I need to cut a small part of the candle mount to install the bolts or completely disassemble the front end to get the bolts installed. Thank you. It's hard to get information on doing this job.

Is there anyway of confirming the correct refrigerant type ?

What’s weight limit on mb200s

Trying to figure out what fault fan means

I tried this for my project but it didn't work. It caused a power cut. What should I do??

My 2011 Silverado 4 x 4 LT had an issue where the plastic grommet on the lower cable broke and had to replace it. This was helpful but one thing i need to commet on good or bad is pay attention of the firment of the "JC" clip mine only went on one way to make the cable stay in place. (Learned the hard way). However this video was helpful!!!

Very informative and helpful thank you very much Sir! :)❤

What length bolts did you buy?

What are this sewer power washer attachment called

Thank you!!! 🙏🏻

Awesome Lou, the 2x4 level, the speaker and lazer! I look forward to watching more of your videos, thanks.

The non-code drain and vent could be a huge factor later. Always hire a licensed plumbing contractor when possible.

Great! Thermal switch. Okay will check mine out sometime

That's a very specific scenario to lead with.

I have the same problem. What is that bolt called that came off and where can I get one?

Hello, do you know how to solve the problem with the base? It does not aspire. A red light appears

What's the weight limit on this?

Im not new to smoking and ive never cut my shoulders like that. Usually cut off as much fat as possible rub a binder on then my rub and smoke at 225 till the core hits 150-170 degrees wrap with aluminum foil n finish the cook till 195-205. Perfection every time

How did you know the whole system was no leaking point before you refilled the refrigerant ?

nice video, thanks

I have just one question. What happens if the generator stalls brakes or shuts down for any reason? Think about that lol

Thanks 👍 worked like a charm .

Same thing can be done with 3 large junk tires attached to metal cables and dragged behind your car.

Been using an inverter microwave for years, even switched my mom's out for one! Directions for microwave cooking on food is pretty accurate for an inverter as well(typically directions are for 1100W). You can just take the microwave's wattage(usually 1200) and divide by 10 to get the closest power level to use. Usually 9 for most stuff. Also you can hear when the transformer turns on and off with old microwaves since it only has one power level, there's a distinct noise change if you listen.

This is a great video. You showed every necessary step, you were to the point, and now I’m pretty sure I can do this with my own sink. Thanks!

Thank you for the updated exploitation!

Well-Done

My journeyman has been helping me come up with a design to build my own racing mower and I’m definitely gonna take a lot of inspiration from this. I’m just lucky my journeyman also has a welding ticket so hes gonna teach me to weld and help me lower the frame. Best job I’ve ever had😎

if the fridge is already empty... couldnt I just wait it out and let the ice melt on its own, behind the plastic panels?

Did you fill in the trench with extra top soil when finished, or did you capture the excavated mud?

Paint your house a lighter color, insulate the walls and attic better, put in better insulated windows, at night open your windows to let hot air out, shut blinds or drapes to stop sunlight coming into the house, something that most people don't know is that window air conditioners are often if not always rated to be put into a wall called a through the wall installation, a window is a wall it's just a wall made of glass so there's really no difference except that the true walls a bit thicker. This thickness is your limiting factor if you have two by eight walls they will likely block some of the vents on the side of the AC unit but 2 * 4 and 2x should be okay. When you do use fans put them in the direction that they're getting hot air out of the house. What this means is to work with physics. Hot are naturally wants to rise so put fans blowing air out at higher windows or blowing air in from lower windows

I wonder if this would work to shred furniture foam. @HowToLou, do you still have it? Would you try this for me 😊

I could be wrong but most generators have to run at a steady 3600 rpm to provide a steady 60 hertz so you don’t damage electronics or electric motors. I would be skeptical running on natural gas without a regulator to get a steady 3600 rpm when loads change.

From Google I found the link to the actual UA-cam cite, clicked on it, then liked it for you. Thank you

Your belt is facing the wrong direction

Thanks Lou for such a great video & taking the time to produce this for us Keurig coffee lovers! Now I have a project to look over my Keurig : )